Emergency checklist
Burst pipe or active leak: what to do right now
Work through these steps in order. Stopping the water comes before everything except safety.
Last reviewed Nov. 18, 2026. Figures are national ranges from the sources cited on this page.
If anyone is hurt or in danger, call 911. If you smell gas, leave the home and call your gas utility from outside [1]. Don't touch electrical equipment if it's wet or you're standing in water [2].
Right now
- Shut off the water. Use the fixture or appliance shut-off if the leak is there (under a sink, behind a toilet, behind the washer). Otherwise turn off the home's main water shut-off valve [3].
- If it's the water heater, turn off its power or gas first, then close the cold-water valve on the pipe entering the top of the tank [1] [4]. Full steps are on our water heater page.
- Deal with electricity safely. If water is near outlets, cords or the panel, turn off the breaker only if the panel is in a dry spot. If the panel is wet or near water, have the utility company shut off power [3]. Don't touch wet electrical equipment [2].
- Open a faucet at the lowest point of the house to drain the remaining water out of the pipes once the main is off.
- Call a plumber. HomeGuide treats a burst pipe as an emergency and advises calling a plumber right away [5]. Ask about the after-hours rate first: HomeGuide puts emergency plumber rates at about $120 to $300 or more per hour [5].
In the first few hours
- Document it. Take photos and video before moving things, and keep damaged items or photos of them.
- Move belongings out of the wet area, especially electronics, paper and furniture.
- Remove standing water with a wet vacuum, mops and towels where it's safe.
- Start drying. Open doors and windows if the weather allows, and use fans and dehumidifiers once electricity is safe. CDC recommends keeping indoor humidity no higher than 50% [6].
In the first 24 to 48 hours
- Get everything dry. EPA says water-damaged areas and items should be dried within 24 to 48 hours to prevent mold [7].
- Pull up wet carpet and pad if they can't dry. CDC advises removing or replacing carpets and upholstery that have been soaked and can't be dried right away [6].
- Call a water damage restoration company if water got into walls, ceilings, subfloors or a large area. See water damage restoration cost and how to choose a contractor.
- Talk to your insurer if you plan to file a claim. We don't comment on coverage; read your policy and ask your insurer or agent.
What it's likely to cost
| Item | Typical cost |
|---|---|
| Burst pipe repair | $400 – $2,000 [5] |
| Water extraction and drying (clean water) | $4 – $6 per sq. ft. [8] |
| Replace drywall (incl. removal) | $2 – $6 per sq. ft. [5] |
Frequently asked questions
Should I turn off the electricity when a pipe bursts?
Only if you can do it safely. FEMA's flood program says turn off the breaker if the panel is in a dry part of the home; if it's wet or near water, have the utility company shut it off [3].
How long do I have before mold starts?
EPA says to dry water-damaged areas and items within 24 to 48 hours to prevent mold growth [7].
Sources
Cost figures are national ranges published by the sources below, as of the dates shown. Local prices vary. We don't invent or adjust numbers.
- A. O. Smith (water heater manufacturer), What to Do When Your Hot Water Heater Is Leaking?.
- Ready.gov (FEMA), Floods.
- FEMA National Flood Insurance Program (FloodSmart for Agents), Five Facts to Help New Homeowners Protect Against Water Damage.
- Rheem (water heater manufacturer), Urgent help.
- HomeGuide, How Much Does It Cost to Repair a Burst Pipe? (2026).
- Centers for Disease Control and Prevention, Mold.
- U.S. Environmental Protection Agency, A Brief Guide to Mold, Moisture and Your Home.
- HomeGuide, How Much Does Water Damage Restoration Cost? (2026).